Above values from ASTM A Higher strengths can be produced by heavy cold work – this may be required for certain applications. ASTM A – 16 Standard Specification for Stainless Steel Wire and Wire Rods for Cold Heading and Cold Forging. This specification covers. See the chemical composition and physical properties of ASTM A Grade annealed Stainless Steel, find alternative materials, and connect with suppliers.

Author: Dosida Meztizshura
Country: Antigua & Barbuda
Language: English (Spanish)
Genre: History
Published (Last): 18 December 2007
Pages: 333
PDF File Size: 20.14 Mb
ePub File Size: 9.54 Mb
ISBN: 335-1-73109-183-9
Downloads: 84985
Price: Free* [*Free Regsitration Required]
Uploader: Vugrel

Material can be manufactured to tensile strength ranges other than those shown in Table 2. ICS Number Code B Product analysis tolerance over the maximum limit for carbon and nitrogen to be 0.

Originally published as A — Such requirements may include, but are not limited to the following: Current edition approved Jan. The following coatings may be specied: Soap is generally used. The material shall also conform to the requirements as to mechanical properties. Packaging and Package Marking 9. Last previous edition A — Your comments will receive careful consideration at a meeting of the responsible technical committee, which you may attend.

An electroplated copper coating is often used. General Requirements for Delivery 4.

ASTM A493 Grade 384 annealed

For smaller sizes, similar mechanical properties apply to ferritic and martensitic grades; however the producer should be consulted regarding somewhat higher tensile properties applicable to austenitic grades. Link to Active This link will always route to the current Active version of the standard.


This standard has been approved for use by agencies of the Department of Defense. This abstract is a brief summary of the referenced standard.

The SI equivalents are in parentheses and may be approximate. A number in parentheses indicates the year of a49 reapproval. ASTM does not give any warranty express or implied or make any representation that the contents of this abstract are accurate, complete or up to date. Copyright ASTM Standard Specication for Stainless Steel Wire and Wire Rods for Cold Heading and Cold Forging1 This standard is issued under the xed designation A ; the number immediately following z493 designation indicates the year of original adoption or, in the case of revision, the year sstm last revision.

It is informational only and not an official part of the standard; the full text of the standard itself must be referred to for its use and application. This specification covers cold-finished and hot-finished stainless steel wire and wire rods for cold heading or cold forging for applications, such as fasteners, where corrosion resistance is a factor. NOTE 1—A typical ordering description is as follows: The values given in parentheses are mathematical conversions to SI units that are provided for information only a93 are not considered standard.

This standard is subject to revision at any time by the responsible technical committee and must be reviewed every ve years and if not revised, either reapproved or withdrawn. A superscript epsilon e indicates an editorial change since the last revision or reapproval. Historical Version s – view previous versions of standard.


All austenitic grades in the annealed condition or annealed and lightly drafted condition shall be capable of passing the criteria set by this specification. Resistance to Intergranular Corrosion 8. The American Society for Testing and Materials takes no position w493 the validity of any patent rights asserted in connection with any item mentioned in this standard.

ASTM A for Stainless Steel Wire and Wire Rods for Cold Heading and Cold Forging

The steel shall conform to the required chemical composition requirements. The following lubricants may be specied: Referenced Documents purchase separately The a4933 listed below are referenced within the subject standard but are not provided as part of the standard. The producer should be consulted when material is required to tensile strength ranges other than those specied. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the risk of infringement of such rights, are entirely their own responsibility.

Your comments are invited either for revision of this standard or for additional standards and should be addressed to ASTM Headquarters.